How to turn a $100 dog crate into a $200 gearbox

Posted May 08, 2018 07:54:15The first thing to notice is the fact that this dog crate is huge.

It has a lot of space for everything, and that’s not the only thing that’s going to be packed in here.

The main room of the crate contains three big compartments.

The first one is where you’ll put the big crate pad, which is essentially a metal pad that’s the inside of the dog crate, and the other two compartments are where you can pack your toys.

The main compartment of the gearbox is very big, and I had to make it bigger to accommodate all the gear, toys, and other things.

I was going to keep the crate pad inside, but since the gear boxes are so big, I had the room for a second gearbox.

I had a few options when it came to this gearbox, but I decided to go with the one that would hold the crate and the toy tray.

This one is actually quite simple to build, and it has three slots for things like the leash, and a small slot for the leash attachment points.

This is where I’m going to attach the leash to the gearboxes side, and then I’ll attach the second gear box to the front of the cage, and so on.

Here’s a quick video of how it’s done.

I wanted to use this kit for all of the toys that you’ll find inside this dog gear box.

It’ll hold up to six toys and I think that’s a good amount of storage space.

The only thing I didn’t want to do was get all the toys and gear into the gear box, which I did, but that’s why I have the gear that I have.

The dog crate was just too big, so I just wanted to have it empty of everything, so that’s what I did.

The gearbox also has a lockable area to store toys, which you can open with a small screwdriver.

The lockable door is a little big, but you can easily lock it in with a screwdriver, which will open the gear and toys inside.

Here is the gear assembly that you get.

This isn’t the most accurate picture, but it does show how the gear works.

Here are the three gearboxes, and you can see that I put the leash in the middle, and they’re aligned to the top and bottom of the wheel.

I’m also holding the leash so that I can easily put the harness into the front gearbox and the leash into the back gearbox so that it’s easy to attach a leash to both gearboxes.

The wheel also has two holes, one for the handle, and one for a leash.

Here you can also see how the leash attaches to the side of the handle.

Here is a picture of the front and back gearboxes that I used.

The two holes that the leash goes into are the front (left) and back (right) gearboxes respectively.

The top and the bottom of that gearbox are where the handle attaches.

If you want to put a leash on that gear box that has no handle, you’ll have to put it in the back of the bottom gearbox as well.

Here you can look at how the handle works.

I also made sure that the handle is secure enough to keep your dog from biting the leash.

The handle can be tightened or loosened using a small wrench, and depending on the type of handle you have, you might need to do it a couple of times to get the right angle.

Here’s a picture.

Here it is in action.

Here the handle in the front Gearbox.

Here it is with the handle tightened up, and with the leash attached.

I used a screw driver to tighten the screw.

Here in the rear Gearbox with the same screw driver.

Here, the handle has a slight bend in the center.

Here the handle looks like it is trying to bite the leash as it’s tightening.

Here I’m holding the handle of the rear gearbox while the gear is tightened up.

Here, I’m loosening the screws on the rear side of that Gearbox, so you can check that the front is tight enough.

Here comes the big problem.

There’s a hole in the top of the leash which has to be drilled out.

I drilled a hole just big enough for the chain of the harness to pass through, but not so big that the chain won’t stick out.

Here a picture showing the hole that needs to be cut.

Here a picture, showing the holes that need to be filled.

Here are pictures of the hole drilled, and what I ended up with after I drilled it out.

This is what the hole looks like after I filled it in.

I ended the hole in just big, enough to get all of that chain out of the way.

Here I’m trying to see how much chain I can get through this hole, so let me know if you have any